{"id":70,"date":"2024-05-02T14:59:42","date_gmt":"2024-05-02T14:59:42","guid":{"rendered":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/?page_id=70"},"modified":"2024-05-16T10:48:31","modified_gmt":"2024-05-16T10:48:31","slug":"users-guide","status":"publish","type":"page","link":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/users-guide\/","title":{"rendered":"User\u2019s Guide"},"content":{"rendered":"\n
\n
\n
\n
Request form<\/a><\/div>\n<\/div>\n<\/div>\n\n\n\n
\n
\n
Online Reservation<\/a><\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n\n
<\/div>\n\n\n\n

1.Every student must submit a duly completed \u201cRequest Form\u201d for the relevant analysis in advance. The form, along with supervisor\u2019s signature    and relevant Lecturer In-Charge\u2019s (LIC) signature, must be provided prior to carry out the experiment.<\/p>\n\n\n\n

2. Samples without supervisor\u2019s approval will not be analyzed.<\/p>\n\n\n\n

3. Once the \u201cRequest Form\u201d is submitted, a time slot must be reserved by logging into the online reservation system.<\/p>\n\n\n\n

4. Only the number of analysis approved in the \u201cRequest Form\u201d will be considered.<\/p>\n\n\n\n

5. It is important to emphasize that the sample analysis will not be performed in the absence of the student.<\/p>\n\n\n\n

6. In some special cases, such as poor quality of data or absence of expecting results, LIC will request special approval from the research supervisor to further continue the analysis.<\/p>\n\n\n\n

7. LIC has right to change and reschedule the reserved-time due to unavoidable circumstances such as instrument maintenance and repairs.<\/p>\n\n\n\n

8. If you are not familiar with sample preparation methods, please contact either LICs or the instrument in charge before sample preparation for analysis.<\/p>\n\n\n\n

9. In UTM, student  have to provide the speed.<\/p>\n\n\n\n

10. In internal mixer, student must submit the cycle time, rotor speed and temperature.<\/p>\n\n\n\n

11. In MDR, Student must submit the temperature and the time that needed to run the sample.<\/p>\n\n\n\n

12. In compression moulding, student must submit the temperature and the time that needed to run the sample.<\/p>\n\n\n\n

13. If the number of analysis is significantly higher, the LIC will discuss with the research supervisor to maximize the fair user policy. The average time taken for a sample analysis is shown below for your reference.<\/p>\n\n\n\n

Instrument<\/strong><\/td>Instrument warm up time<\/strong><\/td>Time taken for analysis<\/strong><\/td>Number of sample analysis per request<\/strong><\/td><\/tr>
Internal mixer<\/td>10 min<\/td>20 min<\/td>10<\/td><\/tr>
MDR<\/td>–<\/td>30 min<\/td>10<\/td><\/tr>
Compression mould<\/td>1:30 hour<\/td>15 min<\/td>15<\/td><\/tr>
UTM<\/td>–<\/td>15 min<\/td>30<\/td><\/tr>
Two roll mill<\/td>–<\/td>30 min<\/td>10<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

14. Students are not allowed to handle any instrument without permission.<\/p>\n\n\n\n

15. If the analyzed samples are not collected, they will be discarded after 48 hours.<\/p>\n\n\n\n

16. DRY RUBBER LAB Facility does not take responsibility<\/strong> on the precision and accuracy of the data.<\/p>\n\n\n\n

17. It is recommended all our users to acknowledge the DRL-FAS for the work done in whole, or in part, at DRY RUBBBER LABORATARY of Faculty of Applied Sciences of University of Sri Jayewardenepura with the following statement:<\/p>\n\n\n\n

\u201cThis research [or, A portion of this research] used resources at DRL operated by Faculty of Applied Sciences of University of Sri Jayewardenepura.\u201d<\/em><\/p>\n\n\n\n

If you acknowledge us, please do not forget to email us a copy of your publication for our records.<\/p>\n\n\n\n

18. If a staff member of the DRL-FAS is profoundly involved in a research project, you are highly advised to add that person as a co-author<\/strong> in scientific publications.<\/p>\n","protected":false},"excerpt":{"rendered":"

1.Every student must submit a duly completed \u201cRequest Form\u201d for the relevant analysis in advance. The form, along with supervisor\u2019s signature    and relevant Lecturer In-Charge\u2019s (LIC) signature, must be provided prior to … Continue reading User\u2019s Guide<\/span><\/a><\/p>\n","protected":false},"author":134,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_ti_tpc_template_sync":false,"_ti_tpc_template_id":"","footnotes":""},"_links":{"self":[{"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/pages\/70"}],"collection":[{"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/users\/134"}],"replies":[{"embeddable":true,"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/comments?post=70"}],"version-history":[{"count":7,"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/pages\/70\/revisions"}],"predecessor-version":[{"id":224,"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/pages\/70\/revisions\/224"}],"wp:attachment":[{"href":"https:\/\/science.sjp.ac.lk\/dryrubberlab\/wp-json\/wp\/v2\/media?parent=70"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}